Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
In the \external\micro-ecc\micro-ecc folder，when i used ”build_all.bat“ to build target，it happened “makefile:83: *** missing separator“ error
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
To the kind attention of Nordic support team,
I have been reading https://infocenter.nordicsemi.com/pdf/nRF52833_PS_v1.0.pdf product specification, where only
aQFN 73...
Hello everyone, I wan't to layout my own PCB board of nrf52840 ,is there any things need to be attention? By the way, if I'm not using Interface IMU to upload my programming...
When I have put the nRF9160 modem into mode 4 or 44, and then issue a status read AT+CFUN? command, the modem erroneously goes online. I have used latest and greatest modem...
