Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi,
I'm trying to connect to the EMQX(what I made on GCP) using mqtt protocal. I'm using the sample code that nordic provides in lesson. Based on the Exercise4 code which...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
Hi,
I have used examples\dfu\secure_bootloader\pca10056_ble application and successfully updated two applications(heart rate and health thermometer) over BLE. In order to...
Hello, i' trying to measure the power consumption of the nrf52840 PDK. So far i have been able to measure the current. How can i go about measuring the voltage and is it constant...
Hello, I recently received a Thingy:52 and was able to connect to PC using J-Link. After uploading Heart Rate Monitor program Thingy is no longer able to be added using iOS...
Hi,
I am facing difficulties porting Mesh examples to IAR.
I am getting the following error : #error "Your compiler is currently not supported." during compilation from...
I'm working with nrf52 dk to read the sensor dht22. i need to follow this steps to make sure the sensor is ready to send data.
Wait until DHT responds and pulls the line...
The problem is that the load was made via application, using nRF Tools in the DFU option, since I wanted to understand what I did with the files and others, but now that I...
Hi,
In nRF51822 proprietary ESB protocol. there have define a "noack" field in structure "nrf_esb_payload_t".
Normally, the "noack" field is set to "false" in transmit...
Hi,
Now,I made a NRF52832 scanner gateway with SDK15.0 and softdevice 6.0.0.
I want it to scan advertiments continuly. So i set SCAN_WINDOW and SCAN_INTERVAL (they are...
I am using mesh sdk v2.0.0 1, 1 client and many server node is successfully provisioned. But when i increase CLIENT_NODE_COUNT (2) instead of 1 only one client is provisioned...
Hi all!
I'm currently trying to communicate with the CR95HF (on the BM019) chip over SPI with the DK52 board.
I'm using SDK 15.0
According to their datasheet, the CR95HF...
Hello,
When I analyse the output of my radio, I see that I have a spurious frequency at 12,8 Mhz.
I supply my custom board with a fidelity power supply so no problem...
So I have implemented the UART BLE mesh code as mentioned in devzone.nordicsemi.com/.../send-and-receive-a-string-via-access-layer .
Now I am able to take inputs from the...
Hi,
1.
I feel really stupid as I cannot make any sense of any of the information found in Product Specification (v3.3), or the online Compatibility Table or past forum...
We can know the state of radio by checking NRF_RADIO->state register value, but is there any way that we can be "informed of" the state transitions of this register instead...
