Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi,
I'm trying to connect to the EMQX(what I made on GCP) using mqtt protocal. I'm using the sample code that nordic provides in lesson. Based on the Exercise4 code which...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
I 've been working with the nRF54L15 for a bit now and it' s been great, but trying to get a bit fancy now and running into problems. I 'm developing with the latest NCS v3...
Runtime environment:
1.IC:52840QIAA ；
2.SOFTDEVICE:s140_nrf52840_5.0.0-2.alpha_softdevice.hex
Development:
PWM signals of 10 groups of adjustable frequency and...
I am trying to establish communication using SPIM. when I checked the macro definition of NRFX_SPIM0_ENABLED it's present in apply_old_config.h. I am using nrfx_spim driver...
Hi,
I have two 52832 (both on SDK 14.2, S132 v5.1) talking to each other using a slightly modified UART service to support more than one connection.
I have this strange...
Hello,
yesterday I measured the current of our device and found out that it looks more as a square instead of spikes when no device was connected. Found out that when I...
In my code , i use P0.6, P0.8, P1.9 to control three RGB LED.
when I use nRF5_SDK_13.0.0-1.alpha, all is fine,
but when use nRF5_SDK_15.0.0_a53641a, the issure like below...
Hello,
I'm new to Nordic SDK and I would like to ask you for help with change of
GPIO IN_EVENT to GPIO PORT event implementation. The reason is we are using
revision <...
Hi,
I'm using nRF5 SDK v15.0 with S132 v6.0. I have two questions:
1. I use the ble_app_uart example. We want to use high UART baud rate, so I change it to 1M baud rate...
The project I am working on stores information in SRAM while it waits for the radio to get in range and transmit data.
I want to know if I can put items in SRAM buffer that...
I'm trying to learn the DFU process and how to include it in a project under development using SDK 15 and the nRF52 DK. I programmed the DK with the S132 Softdevice and the...
I'm having issues with slow directed advertising. I'm having a BLE peripheral where I want the device to advertise (direct) upon disconnects. I initialize the advertising...
My project goal is the following: To get data over USB and sending it to a computer using Bluetooth 5.
I've been looking around for a Bluetooth 5 dongle, but have not found...
I'm trying to sample ADC signal using 12 bit ADC resolution, but the digital signal doesn't match the original one seen in the Oscilloscope.
Here are my ADC configurations...
Hi i'm trying to using link with SDK14.2, and modified to the code with some init api,
when i used the MadgwickAHRS.c i modified, i got some trouble when i try to new a...
i'm have 2 device communicate byte UART protocol, one of them is NRF51822 and the other is some kind of MCU that i don't know clearly
NRF will send request to MCU then MCU...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I modified the example "ble_app_uart". I just remove the ble functions and added gpiote functions to wake up the MCU from sleep...
