در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
I am not able to make software breakpoints working with a Segger J-Link probe.
As an exemple, here is my assert callback function:
void __attribute__((noreturn...
Hi.
I'm using nRF51822QFAC, SDK10.0.0, S130.
I want to use DTM code to get SIG certification.
In your example, there is no source code for S130 but S110, S120, S310....
My BLE application needs to occasionally (1-2 times a year) send large amounts (several kbytes) of data, and I'm wondering about how to make this happen as fast as possible...
I am just wondering if anyone else has seen this issue.
I am working on the ble_app_uart_s132_pca10040 on the nRF52 DK.
Using the Android UART v 2.0 app I can connect...
Hi:
A peculiar problem:
I configured an Arduino (atmega328P) to be a receiver and an atmega8A to be a Transmitter Things are fine. The Arduino receives a 10 byte string...
We are developing a beacon device with 10dBm power amplifier. During software development we noticed the control signals provided by ble_common_opt_pa_lna_t align poorly with...
Hi,
As title ,
I try to add the NUS service that show on the ble_app_uart project into Multi-link project.
But it doesn't work .
I want to a central connected to at...
I want to use PWM on only one output pin. I'm using a nrf51422 and softdevice s130.
I want to be able to set the PWM and then change it again (a sequence). This is to be...
I have tried using the pre-built nRFUart Example in the Master Emulator API (2.1.11.1) and get the above error
I also tried rebuilding - no change.
I do have a PCA10000...
Hi everyone,
I'm seeing a weird issue with one of my two instances of 2ch PWMs where if I receive data from TWI, my PWM1 stops functioning and TWI stops functioning as...
A characteristic can be read/write/notify.
I have seen cases in Nordic's examples where there is an internal boolean "is_notify", and when the user sets it from the central...
I'm using an nRF51822 on a custom board with Nordic's serial DFU example from SDK v10.0.0. I'm trying to find a way to exit the serial DFU without the DFU trying to update...
Hello,
I wanted to know if is any way of changing the Pins for the UART and still get the data through the USB connected from the PC to the DK? Or do I need to always physically...
Hello,
I am stitching together two examples in nRF_SDK11:
I started with example
ble_app_multilink_central
The I added code, includes, to main.c and...
Hello,
I've got a problem, and I don't know what is happening.
I've programmed several nRF51822, and my program doesn't works until I connect the debbuger to nRF51822...
