Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I need a module that I can poll over SPI from my host MCU an output of a FIFO buffer of incoming packets (MAC address and RSSI) on channel 37 Bluetooth. Or a module where...
I would like to close a button cell battery (3V) directly to VDD and define the VDD as ADC input. I would like to measure the button cell battery voltage via the internal...
Dear Sir,
I am interfacing nRF24L01 with Renesas R5F104 Microcontroller on transmitter side and my Reciever is nRF24L01 interfaced with Arduino Uno Board.The Transitter...
I am very new to this so apologies in advance .
When I compile the sample code using Keil for the Thingy i get the error message.
.\_release_v1_0_0\app_thingy_s132...
hi, I am updating the sdk from 12.2.0 to 14.2.0, and using softdevice s132. I get a problem by connecting device using ios devices, but it works fine with android device....
Downloaded the S132 from the NRF52840 site and loaded it onto the NRF52840DK board using NRFgo studio.
Then created a new project in CrossStudio. Imported the memory map...
Hello guys,
I wanted to start to implement the power management feature on the NRF52 using the Zephyr kernel for a bluetooth application. Unfortunately I am running in...
Hi,
Do you know when the PWM or the ADC functionality will be added to Zephyr for the nRF52 chips?
Can we use the nRF SDK inside a Zephyr application to use unimplemented...
Hello,
sorry to have to ask again, but from reading through all the posts I could not quite figure out how much current the SPI should draw when it is active and reading...
Hello everyone,
I am looking forward to 3rd party BLE modules in which I am interested in choosing Taiyo Yuden EYSHCNZWZ
I want to know that can we flash our code using...
I am using 3 nrf52 DKs with S132 and SDK14 / and SDK15 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and...
Hi All,
We are working on nRF52810 chip for on of our beacon project and we are using external antenna on board but
We are dealing with the Reason 8 disconnections.
...
