Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I would like to use the nRF52840 modules for moving nodes. However, I'm concerned that the modules will not be able to cope with high moving velocities to communicate...
Hello, after getting my nRF52-DK I first tried to program it using Arduino IDE according to this guide. Everything worked perfectly as I was able to flash new firmware into...
Hi, Does BLE IPSP profile limits the maximum channels a one? I tried to change BLE_IPSP_MAX_CHANNELS to two, but it results code crashing at nrf_sdh_ble_enable() API. Is soft...
I'm finding some issues in sending data from nRF52832 using UART.
I need to send a string of length more than 100 characters.but when i
try to send,only 94 characters...
hi, I am switch from sdk 12.2.0 to sdk 14.2.0, I could not find softdevice_ble_evt_handler_set() and softdevice_sys_evt_handler_set(). what should I do with these two? and...
Hi,
I'm trying to develop something for nrf52832 and was trying to use the s130 softdevice. Using Kiel uVision 5 i added all the necessary packs, but when I add s130 to...
Hi,
I have two devices and one host. When they are in close area both of them are pairing to one host. When I switch off host, both devices looks like paired to each other...
Having gotten through the hurdles of getting my IAR project to compile and run on Segger Embedded Studio, I am now seeing different behavior between the two IDEs while debugging...
Hello,
In my application (based on app_nus_uart example, with two NRF52832 boards), one of the cases is uploading/downloading files with sizes up to 10MBytes.
In my app...
Can someone explain the reasons/benefits of using the single vs dual bank BLE boot loader?
Actually, why isn't there a single bank BLE bootloader in the example project...
I have following code which should start the app_timer and blink the LED_1.
When flashed, the LED_0 turns on and I can see the "Started." log. But the LED_1 is not blinking...
Hello,
I use nrfutil to generate the dfu .zip file, the error log is listed below. what is the reason? the softdevice is s140. thanks.
>>nrfutil pkg generate --hw-version...
ble_app_uart_c_pca10056_s140 fails with an assertion - I have downloaded nRF5_SDK_14.2.0_17b948a. For the example project examples\ble_central\ble_app_uart_c\pca10056\s140...
Hi,
I am trying to write a 120 byte data through ble to raspberrypi from my android app(I increased the MTU to the required limit). But all I am able to transfer is first...
