I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hello everyone !!!
I've recently started working with Segger Embedded studio for nfr52840. I want to add a new driver into an existing projects.Let's say GPIOTE
I...
Hello,
Recently i am working on UART application on nRF51822 based product.
In UART application code, there is no option to configure the modulation rate.
So, I would...
Dear friends,
if i adjust the tx power of nRF52832, e.g., by calling sd_ble_gap_tx_power_set(), which phase of the current will be affected in the pic bellow? just the phase...
I am struggling with getting a Secure UART(Serial) DFU operation to function correctly when I attempt to enter the bootloader with a call from my app. I am using the basic...
Hi all,
I am working on interfacing an SD card as well as an OLED Display with my nrf51422 on SDK 12.2.0.
Although, both are on SPI and hence i need to configure them...
Hello,
I'm running the SPIS example from Keil (SDK 15.0), but I want to print out the received as the decimal value instead of as a string. If I change %s to a %d in this...
I cannot access any more my nRF52 DK 10040 with nrfjprog ,indipendently from the command I give.
I use Windows10 nrfjprog command line ,i can see and access JLINK drive...
Hi,
I am using two nRF52832 and one nRF24L01+.
My topology is as follows: nRF52832 A<---> nRF52832 B<---> nRF24L01+.
where "A <---> B" means that A communicate with...
To check, in sdk 15.0, there are no pca10040e (s112) examples of ble_app_buttonless_dfu & secure_bootloader because examples were not yet ready for sdk 15.0 release, or something...
Hello,
I'm currently using the nRF52832 chips with SDK11.0.0 and s132. I'm currently trying to modify the TX power level for advertisement. I'm seeing many ways that I could...
HI, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v2.0.0) and some other sensors which drivers written by using nRF5_SDK_15.0.0 . Can you help to understand how to do...
Is it possible to program the nRF52840 dongle using the nRF52840-DK using SWD?
I tried, but it failed. From the nRF52840 schematic, it looks the chip is running at 1.8V...
Hi,
Win10 can run a subsystem, which is Ubuntu for me, in the powershell environmental.
But I can not connect the pca10040 debugger. it show error when I try to erase...
I am trying to build a run time test routine that will return the ppm offset between the 32khz and the 16mhz clocks.
Can i use PPI to hook 10 clocks 32khz ticks to capture...
