Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I have the preprocessor define CONFIG_NFCT_PINS_AS_GPIOS in my code, and GPIO functionality for P0.09 and P0.10 are working just fine for me...
My issue is that even when...
Hello!
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
I want to send advertisings at regular intervals (every second...
Hi,
Is it possible for an 3 party BLE device like an mobile device like an Android/IOS Phones or ESP etc to participate in mesh notwork if so is there any documentation...
I have been unable to perform a DFU over BLE using the bootloader_secure_ble example.
I am using SDK 14.0, nRF52832, S132 with a custom board, along with the nRF51 Development...
Hello,
I want to factory pair nRF52 to nRF52 connections (NUS) with a factory set key but i'am lost.
I digged in NFC pairing but it's too complicated for my understanding...
Hello,
i use IAR EWARM 8.20.2 and SDK 12.3.
I compiled the blank Blinky example from the SKD for the pca10040 without any Errors or Warnings. When i load the .hex to the...
I use IAR EWARM 8.20.2 and the SDK 12.3 because i want to use the S130 for the nRF51.
I installed the provided MDK_8_11_1_IAR and now there are two options for Nordic Semiconductor...
Hi,
Note: i have already posted this topic , but no one helped me , stay hopeless about the solution, so i try again with this new topic.
my problem is :
I tried to...
The comments (and the name of the function) say it returns an address, of an event register. So the return type should be a pointer type? This causes compile errors on stricter...
Hi,
I have two problems with pc-ble-driver, I've tested hrc_v5 example program on my Linux machine, along with connectivity_2.0.1_115k2_with_s132_5.0.hex firmware (using...
We have set the peripheral ADV interval & central SCAN interval as below configs, we found that the connection time is unstable, from 125ms to 980ms, we expect to get a stable...
nRF51822, SD 130 v2.0.1, SDK 11.
Dear community,
I am experiencing an issue with disconnection on iPhone (iOS 11.2.5). After connecting and bonding with device (in iOS...
Hi,
I am using SDK 14.2.0 and SD 132 v 5.
When trying to combine ble_app_beacon with twi_sensor, I get the following error:
..\..\..\main.c(89): error: #253: expected...
