Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Dear,
I am trying to test nRF52840 Preview DK.
Is there any method to test bluetooth 5.0 feature or spec?
Especially on speed and distance.
Thank you in advance!
Dear Madam/Sir,
I'm working with SDK14.2, softdevice5.0.0-2alpha, s140, and nRF52840 through the DevKit.
I'm recurring to the fstorage API to read/write/erase flash while...
Does enabling POFCON on nRF51822 lead to any increase in power consumption?
If yes then what is the value?
I struggle to find any information in Reference Manual or Product...
Hi
i am new with nr24L01 module , i am currently trying to configure them but , i am not able to read the RF_CH register just after write into it ? so i don't know if the...
Hello. I am using ble_app_uart from sdk14.2. I use pca100401, softdevice s132.
Advertising is generated using timer RTC. Board advertises and stops advertising without errors...
Here is our requirement.
We want to have four transmitters based on nRF2460 and more than 100 receivers. It means there will be four broadcasts.
Each receiver should...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
I have build the light switch demo, it works properly. But I want to make multiple sensor node that takes data from sensor and send to single relay node. I am little confused...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
