Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am developing a BLE remote which will work with Android and iOS(as a remote shutter for camera). I used nRF's HID keyboard example as a base but it does not have volume...
Hello,
we are using the example ble_app_uart_c as basis.
I found out , that it takes about 650ms after Reset / Power up before i can send a string over ble.
The connection...
Hey there, I have a problem when use the command nrfjprog --memrd xxxx.
I was running a simple blinky led example on a nrf52 custom board, then i read some information from...
Hi all,
I am working on a project which receives data from UART (15 bytes at every 40ms interval). I want to store 1 minute of data on the NRF52832 RAM before sending it...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
Hi,
IC : nrf52832
SDK : Mesh_v1.0.0
I am testing the light_switch demo of the Mesh_v1.0.0.
I don't have 32kHz osc on my server board, so I have to change the clk...
Connect USB to PC, no "JLINK" device. But connect USB to PC and press reset button at same. I can see "BOOTLOADER" device.
How can I get my board to normal?
I am trying to create a network mesh using the multiperipheral example.
In the original version the communication is possible only:
central >> peripherals
peripferals...
Hello,
I am wondering if you have any plans for implementing a Softdevice that supports BLE mesh network on nRF52832 in near future?
If not, if I were to implement it...
I'm reading about beacon scan response requests and scan response packets, where a client (like a phone) can request the beacon respond back with local name and other info...
Hello,
I need to implement mesh networking capability in the beacons which are ble5. Can anyone explain me how do we achieve that?
I want send specific data via one...
