Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hello, Thank you for helping me to interface the PCF85176 (40 x 4 universal LCD driver for low multiplex rates) with Nordic nRF52 development kit board. I need to write the...
i have a few question, i bought this " www.skylabmodule.com/.../".
if the device has a sample code loaded?
where are the example codes for the device?
i want connect...
Hi everyone,
I recently acquired a nRF52832 Breakout Board from Sparkfun. I have been using it for a few weeks now and everything was fine. I was programming it using the...
I use DFU function to update APP. and when i execute the flash write operatin in APP,then afer the dfu operation,bootloader can not jump to the APP. it keeps in bootloadr...
I am using nrf52832, SDK14 and sd 132.5.0. I want to disable SAADC after measuring battery level then enable again when I want to measure it again like in this post . When...
Hi, I want to know how to properly indicate for the function
spi_send_recv(...)
that I'm sending or receiving data on SPI.
On other platforms with library function...
I'm using the SPI driver and experiencing a hang in the SPI driver because the SPI interrupt is not raised. The reason is in this code from the driver:
p_cb->bytes_transferred...
Hi,
my device does some UART communication. Because temperature drift of HFINT is to large, the external HFXO has to be used. To make things worse, this is a low power...
hello,
I modified the beacon example that allows me to modify major and minor value from mobile app,
but when i restart the nrf52840 dev board, the modified values are reset...
Hi,
I need to get at least 3 sensors data (Accelerometer and Gyro) simultaneously and I am thinking to use the Nordic Thingy:52 for that. Our application sends these information...
Hello Nordic Devzone,
I have problems with twi/i2c init code on a Micro:bit, nrf51822.
The accelerometer is a Freescale MMA8652FC.
I use Segger Embedded Studio for ARM...
Hi there,
We started to notice that we have been getting random disconnects with the reason BLE_HCI_CONNECTION_TIMEOUT. After profiling our device, it was found on one...
Hello everybody,
I try to use fstorage in SDK 14.2.0 S132 with Segger Embedded Studio IDE.
I write this;
static ret_code_t fds_init (void)
{
ret_code_t ret = fds_register...
I have been using the RF Digital Simblee chip ( also with the NRF51822) with my Android app and Java code to communicate with the Simblee chip as a peripheral.
I have been...
hi nordic;
i need your help, i'm trying to code a control of gpio over the BLE i have an app on android with it i can establish connection and see the service and charactrestic...
