Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
I worked on the nrf51 for some years and recently moved over to the nrf52. PPI is a new interface I am exploring. I am having trouble restarting a RTC which was started...
Hello!
I have been lurking around the Thread SDK and I wonder if it is possible to get the IP-address of the device, and if so, how? I am stuck here so any help would be...
My nRF8001 device uses encryption with just works procedure.
Establishing a bond between nRF8001 and peer device as well as reconnection works on Android.
On iOS reconnection...
Hi,
I have download nrf5_SDK_for_Mesh_v1.0.0_src and want to start with nRF52840 DK and 52832. I could use EmbeddedStudio to flash it to 52840. Is there a app on the phone...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hi,
I have an application where both radio notifications and flash operations are used.
It seems that every sd_flash_write() generates two radio notifications. So during...
Hello Everyone,
I am using raytac's BLE module (nrf51822 chip antenna version, 32kb RAM 256 kb Flash ) (www.raytac.com/download/MDBT40/MDBT40-ANT-D.pdf) in our product...
Hi,
I have a problem with NRF_LOG_INFO() macro - it only shows messages form main.c file but not from another .c files in project. Why this could happen?
I work in Eclipse...
Hello,
is it possible to use a external clock e.g. a digital output of a TXCO. As source for the LF clock. So the same clock source as used for the host uC can be used...
Hi!,
I'm newbie with nRF52. I have a nRF51 Development Kit and a nRF52 Development Kit.
I have installed nRFconnect (for Ubuntu 64 bits) in Fedora 24 Workstation (64...
Hi! I have tried to use USB CDC ACM in my project but after running the USB CDC ACM example in the SDK, I found out that the example have the issue of not sending the data...
Hello,
So I'm constantly reading data using i2c into a variable. How do I transfer the data in this variable to the pc? It's just an array.
I understand that I have...
I am looking for a smallest size transceiver with an antenna done as part of the PCB layout (no external antenna needed). The simplest RF PCB layout is preferred, single frequency...
Hi, I purchased a Sparkfun Breakout board for the NRF52832, but the bootloader on it seems to be extremely unstable. Hence, I've decided to flash the NRF52832 directly from...
Hello,
I already checked below link, but want to clarify the limitations of how many concurrent sessions are allowed in Soft Device initialize.
devzone.nordicsemi.com...
