Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
Hi everyone!
I'm using the nrf_soc API for get random numbers from the rng and erase and write the flash memory.
In my code, I include the nrf_soc.h file, in the header...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello,
I tried to do DFU using MCP 3.10.0.14 and I'm getting the error:
"Error during firmware upload. Timeout while waiting for response for START DFU"
How do I increase...
I have secure dfu working on the pca 10040, and being able to download my own signed app.
However I want to turn NRF_LOG and at link time I get several messages of "._build...
Hi,
my application consists of long waiting time without connection (hours, possibly days, weeks), then a central connects and downloads data, and then again long waiting...
Hello all!
Sorry for what might seems an obvious question, my skills are what they are :-).
We have a small circuit based on nrf51822 chip.
Our software is currently...
Hello, I am new to embedded world.
I wanna know that how do i create a new template/blank for programming in uKeil?
Right now, i directly open an example from the SDK...
Hi there,
I am currently working on a project where I would need to use the Segger J-link needle programmer with 6 pin header. We have produced the board and after following...
Due to the PWM driver having intermittent issues we had to replace it with a TIMER/PPI/GPIOTE setup.
The PWM is working great in this way, but now I'd like to have one of...
Hi All,
i am using Stpm32 energy meter board.
i have gone through the data sheet completely.
i want to read and write the register values
i am trying to write 0xABCD...
Dear All,
we have been working on a very small PCB design using nRF52832. Some time ago, in another thread , I asked for an Eagle footprint for an antenna and got the quick...
compiling abc.c...
abc.c(26): error: #5: cannot open source input file "boards.h": No such file or directory
#include "boards.h"
abc.c: 0 warnings, 1 error
which file...
hi,
i am working on example programs. i want to add dfu service to example hrs code.
added ble_dfu, bootloader_util_arm, dfu_app_handler.c files to example ble_hrs code...
Hi everybody
I run SDK v11 - ble_app_keyboard on nRF52-DK and wants to use UART to print log.
When I set NRF_LOG_USES_UART=1 & ENABLE_DEBUG_LOG_SUPPORT in Keil C's define...