I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
Hi, Everyone
I am developing based on ble_app_uart at nrf52832 (softdevice s132)
I modified the program slightly.
- After the connection is confirmed
- Send 100 bytes...
Hi Devzone:
I have build up a environment that are
1. a thingy52 with mesh-briadge
2. a thingy52 with mesh-node, which is control by segger-debugger, and it shows
...
Hi everyone,
On my actual configuration I can connect one smartwatch to the nRF51422, and re-connect it later if the communication have been interrupt.
However when I...
Hi Everyone,
I've looked around at the Nordic documentation before asking this question but can't find any good example. I am looking for an example to create a repetitive...
hi
I need to set a pin high when i make a connection to the device .so i set to output direction in main.c file.i have include gpio.h and nrf_delay.h file in main file ...
I'm using the nRF52382 with SDK 14.0 and softdevice s132 5.0.0, and I need to send up to hundreds or thousands of kilobytes to an Android phone over BLE. I need to optimize...
I have a custom beacon with:
nRF5_SDK_12.3.0_d7731ad
I am using:
\examples\ble_peripheral\ble_app_beacon
With:
\pca10040\s132
When I change the value:
int8_t tx_power...
In my project, I want to store data in the form of hex or bin file in the flash memory and send it via spi to the slave device. Can anyone suggest any example on how to start...
As far as I know NRF52840 SoC has multiprotocol radio: "The new radio supports multiple protocols including all the new features of Bluetooth 5 plus 802.15.4-based protocols...
Hi,
we are working on beacon project, we are facing current consumption problem.
When we dump the code in nRF52DK we are getting around 20(uA) current consumption.
When...
As per recommendations with SDK15 I'm using the nrfx drivers for peripherals. When I attempt to compile, the linker fails as it cannot find the function nrfx_saadc_sample_convert...
