Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi new to Bluetooth, but familiar with Radios and embedded devices
I have 2 devices that only connect to each other.
in the interest of extreme battery conservation I...
I am using a BLE UART friend module and I am trying to set the GAPIntervals parameters. I realised that when I set my max conn interval parameter above 2000ms, the device...
I am planning to use the nRF51822 and the s130 soft device to manage data coming back bluetooth sensor nodes. It is likely that there will be more than 8 peripherals, although...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...
Hello,
My system is one device with multiple host, these host will connected to the device on irregular basis.
The host action are listed below:
scan->connect->write data...
hi, i'm going to do some project with nrf51822 and SDK 6.0.0.
i just made up ble connection between phone and the chip.
and i want to send data some fixed time periods...
Hello,
I think there's a bug in the app_uart library in SDK 10 that occurs when the FIFO is enabled.
Using SDK nRF51_SDK_10.0.0_dc26b5e, I was trying to write data to...
I'd like to control a DC motor using PWM (PWM0, pretty straight forward).
To determine motor speed I disable the PWM every 5ms (TIMER1, pretty straight forward) and measure...
Hello,
Our application consists of 100 BLE static centrals and 1000 BLE moving peripherals. Is it possible to hide our BLE peripherals to be visible only by our centrals...
Hi,
i'm testing an application on nRF52, with nRF5_SDK_11.0.0-2.alpha and SoftDevice 132.
I took the ble_uart example and added a custom service with some characteristics...
