Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
Hi everyone,
I was wondering if there are any issues turning on and off the ANT transmitting channel during run-time of nRF51422 with this:
err_code = sd_ant_channel_close...
I want to use master spi mode ,but when I build the file,it is always error.I operate like this ,First I open the project in ble_peripheral\ble_app_hrs\pca10040\s132\arm5_no_packs...
"Hi Guys, my nRF8001 BLE is working perfectly, But recently i was performing regression testing to check BLE connection, their i faced one issue after 10 minutes from nRF8001...
I am using SDK11 on a nRF52 board. I had some success in DFU, but also had issues.
Was able to upload the bootloader successfully using Master control panel. But it always...
I use the nRF52832 IC of WLCSP package.
In addition, it sets as follows:
{.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16, \
.rc_temp_ctiv = 2, \
.xtal_accuracy...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
We have noticed that when our application is trying to call GATT disconnect while nRF master app is running, our app fails to disconnect. More over, when our app connects...
Hello everybody,
I am trying to pair module nRF51822 with Heart Rate Monitor device with the Surface Pro running on Windows 10 with no success. I see the module but when...
This question is a follow-up to this post . After performing several tests and understanding that some phone are more limited than others in terms of the number of exchanged...
Hi,
my device resets on executing sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler);
I have external 32KHZ crystal. I also know that software works because...