Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK 6.1...
Hi,
I use an nRF51822 QFAC A1 and my goal is to disable BLE in a powerdown mode, then when I press the pushbutton I want to restart BLE.
Tried using BLEDevice::shutdown...
Hi,
I'm using nrf52 dk(PCA10040). I want to disable the SAADC between readings to save power. I am calling the function nrf_saadc_disable() to do so. It seems to disable...
Hi,
I am having some trouble to make NFC Tag emulation working with "ble_app_hrs_rscs_relay" example application in the nRF5 SDK v11.0 on a PCA10040 board. Actually I did...
Hi all,
i have a little problem with the #define NRF_LOG.
I have this warnings, and i don't know why.
Warning[Pg004]: macro parameter " VA_ARGS " is used in both expanded...
Hi,
I would like to generate PWM waves with on/off period as low as 10usec.
How to stop the PWM and restart it? I tried this but does not stop the PWM:
void pwm_start...
I am trying to advertise my eddystone UID,TLM and URL frame on advertisement. Here by board is in peripheral mode.
I used radio_notification_init() function where i have...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
It seems like there are several asynchronous things that happen and it's unclear what had proprioty over each other. I assume interrupts asynchronously interrupt everything...
