Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...
I am using Thingy 52 and I need to use multiple sensors on the board. But the API reference is really poor and there is no examples on this. So I don't know how to configure...
I'm trying to debug a high current issue on a custom board based on the nRF52832. I'm currently loading a modified blinky app (entire main.c included below). On the nRF52DK...
hello,
I am using nrf52 DK and MPU 9255 .I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in...
Hi all,
I have a Thingy52 and a nRF52-DK.
I have successfully setup 2 different Eclipse projects to compile code for both hardware.
On the nRF52-DK, i was able to build...
I am developing Firmware for NRF51822, S110 in Eclipse. I Heard that there is two mode in Firmware. 1. Debug mode 2. Production(release) mode. Is there anything like that...
Hi,
Currently I am browsing the mesh sdk to get enough information for my own implementation,
However sometimes its quite difficult to see what a C/H file actually does...
Hi,
I am trying to use nRF52832 dev kit(pca10040) as my connectivity board and STM32L4 as my application board. I have flashed ser_s132_uart(examples\connectivity\ble_connectivity...
Hi,
I have seen alot about the declaration process with the Bluetooth SIG but couldnt find my specific case.
We made a BLE application with the NRF51, a PCB Antenna, SD130...
I haven't found specific documentation on this so I would like to be absolutely certain that the fields in the softdevice info structure are used how I think they're used...
Reffering to the boilerplate: NordicSemiconductor/pc-nrfconnect-boilerplate
Can someone make a quick guide to create a reducer that is connected to the nRFConnectCore[0...
Hi,
I am running Keil uVision V5.23.0.0, debugging a 51822 using the J-LINK / J-TRACE interface built into the chips
My code uses SD110, SDK 7.2
I need to get ABSOLUTE...
