Hi Nordic team,
We are developing two types of devices based on the Zephyr examples:
periodic_adv_rsp
periodic_sync_rsp
Our design uses the following...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
I am using nordic_sdk_10 with nrf51822 USB Dongle. I did a eraseall
flashed my softdevice and dfu bootloader and did a reset. Now i can see advertisement report DFU_Targ...
I am using a custom board with NRF51822-QFAC-R7 and Master Control panel on Android. The DFU is working with test images from SDK130.
BL : examples/dfu/bootloader/hex/dfu_dual_bank_ble_s130_pca10028...
Hi all,
I have been trying to get my Nordic nRF51822 transmit continuously on a particular channel for FCC certification. The Test lab wants me to test the product in 2402MHz...
Dear Forum Users,
I am trying to send the data in a burst. Thanks to this post I have managed to achieve ~2,5 kB/s. However this lasts only for few seconds. Then the stream...
When i load the example radio_test pca10040 in Keil i get the following error messages
Error #544: Required Software Pack 'ARM.CMSIS.4.5.0' is not installed
Error #544:...
Hello
I plan to use two Bluefruit LE Micro devices that contain the nrf51822 as BLE beacons.
I also plan to use a BLE receiver (on another arduino) to receive the beacons...
Hi,
I'm using GCC with SDK11 on linux. I'm able to build successfully. When I try to run "make flash" or "make flash_softdevice", I get error nrfjprog command not found...
I just got the nrf51822 evaluation kit. I followed the instruction and installed everything per instruction. When I tried to open “Blinky” project, I am getting the following...
Hello,
I have a peripheral based on the nrf52 that connects to my Android phone already in direct advertisement mode.
I am trying to get a NRF52 central working with...
Hello! I'm trying to use the PWM on a board containing an nRF51822 device. However, simply including the nrf_pwm.h file multiple errors are trigered, such as the following...
Hi everybody !
I try to use nrf52 DK with OSX
I follow this link
devzone.nordicsemi.com/.../
and I have a problem with this step :
launchpad.net/.../ download
...
hi,
i tried to make a ac dimmer circuit controlled with dc
i use nrf51822
this is my dimmer circuit
aaand this one is zero crossing detector
finally this...
I've been puzzled after looking at the current draw figures for the nRF52832. If the advertising interval is supposed to be 20ms.
Can someone explain why the advertising...
