i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi all,
I'am using nfc url record from nRF5_SDK_11.0.0-2.alpha.
The example works fine on PCA10036 but not PCA10040.
No ITs are generated on µC.
I'am using Nexus 5X...
I am developing an code which requires use of multiple Timers.
I am using Sdk 11 here when i try to initialize timer there is no field for APP_TIMER_MAX_TIMERS in APP_TIMER_INIT...
Inorder to create a c++ wrapper in nordic SDK , i have to
change the Makefile so that it can compile both C++ and C.
in the example the makefile already has gcc added but...
I would like to have BLE using 51822 and audio using a separate BT classic chip on my device. Are there any products in the market that use separate BT chips for LE and classic...
Hello everyone,
I would like to ask that when my project will get the event(BSP_EVENT_SLEEP、BSP_EVENT_DISCONNECT and BSP_EVENT_WHITELIST_OFF)
With the example,in the...
Hi,
I am evaluating the NRF52 with PCA10040 board and nRF5x_SDK_11.0.0.alpha.
I want to create Wave Forme as below.
Out[0] pin transit low to high at compare 0, Out...
I noticed S110 is not listed as supported by nRF5 SDK11. However, no supported SoftDevice seems to offer the same functionality as the S110 (Peripheral only protocol stack...
Hi,
in SDK v9, i tried to compile the bootloader example, but:
/usr/lib/gcc/arm-none-eabi/5.3.0/../../../../arm-none-eabi/bin/ld: region `FLASH' overflowed by 6944 bytes...
Did anybody know how I could determine the connection interval for a established ble connection between an android (4.4) central and a (e.g. nRF51822) peripheral?
I've been having a little bit of an issue trying to parse UART data that I am receiving from an external device.
Where I'm having issues right now is comparing an incoming...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
Hi,
We are developing a product using the nrf 51422 where the power source is a 3 phase generator.
We rectify and charge on a supercap where the uProc is being supplied...
