Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
I am trying ble_app_uart example of SDK 15.
When I do not connect Uart port (TX, RX) to other peripheral, I get fatal error (log via RTT).
```
0> <error> app...
Hello! I am now using nrf52832 sdk14.2 development, as a slave device, need to be bound to the phone, I now want to know the maximum number of allowed bindings and the current...
Hi support team,
I'm using nrf52840 and SDK 15.0. I need to add buttonless dfu service to my application so that my device could be able to upgrade firmware OTA.
However...
When flashing SoftDevice S130 v2.0.1 with nRFGo Studio ( JLinkARM.dll 5.12f ) and softdevice protection enabled, the UICR.CLENR0 is written with value 0x00B00100 (~11M Bytes...
Hi
I would like to create bin file that contains: softdevice, bootloader, maIn application.
To do so i have programmed sofdevice and bootloader via JLink:
r erase loadfile...
Hi,
we are using mesh SDK 2.1.1 over nRF52832. In that, we had developed our custom bootloader, which was based on UART interrupt to receive commands & data from the host...
Hi,
I am running into a problem on PAC10056, please help, pca10065 used to work fine, don't know what caused, I cannot run or debug code on it through SEGGER, I got
...
Steps to reproduce:
1) Set up slave device
Device: nRF52832 SDK: v15.0.0 Soft Device: S132 v6.0 Examples: Any 6lowpan example (including ipv6_medium_ble)
Disable 6lowpan...
When adding two more characteristics to my custom service, I get error #4 which is an out of memory error. The log is working but it does not show the settings for what I...
Hello,
I'm working with SDK 15.0 and Softdevice S132 6.0. I have two nRF52832 boards (the BMD-300 Evaluation Kit and the SparkFun nRF52832 Breakout ).
I am running ble_app_hrs...
I am quite confused about how to go about programming the nRF52840 Dongle. The "programming" page on infocenter says that it can be programmed through the nRF Connect Programmer...
Hi everybody!
I would like to ask the following nRF52840 has the function of preventing current reverse irrigation?
Or what circuit prevents nRF52840 current from flowing...
Hi,
We're designing a BLE module, which is fairly straightforward. The design contains a nRF52832 + SKYWORKS SKY66403-11 FEM. We set the nRF52832 to transmit at -4 dBm and...
Hello,
I'm working on Keil with SDK 15.0 and Softdevice S132 6.0. I'm trying to run the Nordic UART Service example. I have two nRF52832 boards (the BMD-300 Evaluation Kit...
I have quite a few SPI peripherals to be interfaced with nrf52840 chip, for example, Ethernet plug, ATWINC1500 WIFI module etc. What example should i start with to get an...