Hi,
I'm working on a custom board based on nRF52840 and a 2.9" ePaper display (SSD1680) connected via SPI using the mipi-dbi-spi interface. I'm using nRF Connect SDK v3...
I am trying to create a custom sensor for CT1711 temperature sensor. I have created the sensor driver code and device tree binding, but it won't start (initialize) and the...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hello,
I’m working with the Matter Light Bulb sample in nRF Connect SDK v3.0.0 , and I’ve run into build issues when enabling certain optional commands in standard clusters...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hello,
I am using S110 8.0 soft device and using the example Nordic_UART. I am able to compile the project file in KEIL and flash it onto my board. I don't see any errors...
We are using the low power comparator on NRF51882 RayTac Module (Vcc=3.3V, Vref = 4/8), with which we are making a precise high impedance measurement!
I found some documentation...
I've been sending various BLE addresses to the nRF51 and am getting some inconsistencies of what addresses are being deemed valid.
I am using BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
I am using uVision 5.18a with MDK-Lite ARM toolchain and I downloaded nRF examples for SDK 11.0.0-2.alpha with Pack Installer.
Then I tried to compile " /ble_peripheral...
Hello everyone,
I would like to know, if it is possible to send data (power data) from a NRF52-DK to a Garmin Display Device. Do you know any application, project example...
I wanted extract BLE_GAP_AD_TYPE_128BIT_SERVICE_UUID_COMPLETE that i receive while scanning and compare it with 128 bit service uuid that i defined.
i have seen how ot...
Hi,
I am trying to debug my code in Eclipse using J-Link.
Whenever the code executes vPortStartFirstTask() in vTaskStartScheduler() the debugger stops and I can't debug...
Hi,
is there any simple way to obtain current PWM value if nrf52 PWM module is used to produce complex waveform from RAM array? The task is to get currently settled value...
Hi there,
I am new with nRF52 using SD332 and ANT+. I would like to ask if the nrF52 with SD332 can be configured as ANT+ central and ANT+ peripheral in the same time....
I have a query that is similar to the question below
https://devzone.nordicsemi.com/question/44424/how-do-i-switch-the-target-from-a-nrf51422_xxac-to-nrf51422_xxab-in-keil...
Hi,
We are currently considering the packaging design of a device which will use a nRF52. During housing assembly, the populated, but unpowered, PCB will be exposed to...
Hello.
I have a question.
I use nRF52 and S132v2. I found some programs of nRF51, they use S110, S130. What change does it with difference of Softdevice's version number...
Hi,I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master and tested it on NRF52(PCA10040) development board it advertising Eddystone-URL frame successfully and...
hi
i have nrf51422 v2 that use sdk v6 and s210 v3
when i download an example on my nrf and run it to see error check its not returning anything
in s110 i have error...
Hi, In my custom project I need to add two 128-bit uuid services and also I need to use pstorage to protect the application data from power loss. But I got the problem is...