Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I want to use the radio interrupt to receive data, but I only entered the interrupt once at initialization, and I can't enter the interrupt again. But use the commented out...
Hi,
I'd like to know: when using Buttonless Secure DFU Service without bonds, wich is the proper way to prevent a central device to s et a new advertisement name for the...
Hello,
I've got some trouble using Nordic Uart Services,
I am using ble_app_uart example and after connection receiving bulk data from mobile app & sending it on UART...
Hi,
I have build pc-nrfconnect-rssi accodring to instructions. Though the locally build version responds very slowly compared to the officially installed version. No matter...
I am using a nRF52832 and v14.2 of the Nordic SDK. I have a question about the PWM Driver. I have the pwm driver working and driving an LED, but it is unclear to me how to...
Hello!
I am currently developing an application for the nrf52832 using Segger Embedded Studio as my IDE.
The application is not utilizing any softdevice but I would...
Hi,
We are using an nRF52832 with Soft Device S132 in a project. It has been requested that we should advertise as connectable with our own service and characteristics,...
Hi
In the NRF_MESH_PROV_EVT_COMPLETE event, I call
ERROR_CHECK(dsm_address_publish_add(m_next_unprov_address,&m_device_address_handles[m_next_unprov_index])); ERROR_CHECK...
Hello,
I want to be able to toggle blocking RTT output when using the log module.
Before in SDK13 I could just set SEGGER_RTT_CONFIG_DEFAULT_MODE to 2 in the sdk_config...
We are developing a system with multiple sensors that are spaced far enough apart that the furthest sensors won't be able to communicate directly with the user's device (also...
Hello everybody.
I just startet developing with nrf products and I'm facing a problem there.
I'm currently developing a System based on the ble_app_uart_c example. I'm...
Hi,
I am working on secure OTA in my custom Board which is having nrf51822.
I had done secure OTA successfully with SDK 12 but when i am trying to update the code using...
Hi, I want to measure Round Trip Time (RTT) varying data rate
However, when using coded phy, the RTT shows extremely long time
Using 1M or 2M with connection interval...
Our nRF52832 software detects the arrival of characteristics via writes from the Central and reformats the contents and sends them out in a UART message.
I've built an...
Hello, I want to create a simple example code with the leds ws2812b from neopixel from github.com/.../nrf51-neopixel. I need help to build the code.
Regards.