I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
Hi all,
We are ready to have our product released and need to have it tested and certified for release in the following markets:
North America = FCC IC
Europe...
Hello,
I would like to configure the NRF51822 as a Peripheral to receive data from a smart phone, and then call a routine when the receive process has been terminated....
I'm using the nrf52832 and I need to stream audio from an SPI connected memory chip, to an I2S connected amplifier. Is there a way I can have the SPI device stream data directly...
Hello,
i have the following setup: nrf52 as peripheral, smartphone as central.
Peripheral's purpose is to be an interface between appliance and smartphone. It has no pairing...
Hello,
For more "simplicity" I have devised my own OTA update procedure. It relies on image information being embedded in a dedicated section (I have modified the linker...
Hello,
I have succesfuly used ble_app_hrs--longwrite examples provided in dev zone to receive >20bytes from NRF Connect with my pca10028 board. How can I send >20 bytes...
Hello
I am trying to build a project, the problem is that the project is not linking properly, it compiles for sure. During link process I have this errors:
C:\nrf52\workspace...
Some questions regarding offset calibration when doing single samples (or burst mode) from multiple input pins:
Can SAADC offset calibration be performed after SAADC...
I am developing a BLE peripheral application on nRF52832 and SDK 14.3.
I have been power profiling my application and quite happy with the results, except for when the...
Hi there,
I was trying to understand "sleep" power modes of the chip (CPU + Peripherals) in a bit more details - but my understanding is that everything is handled by the...
Hi,
I am facing some issues on enabling timer1 with s132 (nrf52832 pca10040) enabled. i am using the basic timer0 example code as reference and it was working without the...
