Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Can "mbed HRM1017" communicate with ANT+ devices? Because in the offical product page it says " Nordic nRF51822 System-on-Chip combining Bluetooth v4.1-compliant...
When my device received name change request from central, I can catch this event (for updating device name in FDS) by callback *_on_ble_evt , event ID BLE_GATTS_EVT_WRITE...
Hi,
I am trying to port my Application from SDK13.0 to 14.0.
I have completed the porting. But the code is not working.
In Service initialisation there are issues...
Hello,
I use the nRF5 SDK 11.0.0 and with it we can easily build the examples with armcc from Keil, or with gcc (arm-none-eabi-gcc) from the command line using your Makefiles...
The current configuration looks as follows:
IDE: Eclipse
Toolchain: ARMGCC
SDK: SDK5_NRF_14
DK: NRF52DK-PCA10040
I am trying to port the 'bootloader_secure_ble'...
Hi,
I've combined the secure serial and ble bootloader and using it for my custom board. I tried flashing my application hex over serial using nrfutil. I get a device programmed...
Hi,
I am working on the nrf51822 board and i am only the PAC20006 board version seems to be working on it. I am using sdk 11 and soft device version s130_nrf51_2.0.1 s suggested...
Planning for Evaluation of nRF52810.
I am thinking of using nRF52 DK for this and i want to know if there is any beacon with nRF52810 which i can use for this evaluation...
Hi All,
1.One master BLE has to connect to Slave BLE, then both device should read other RSSI and sent the data through UART.sending the RSSI should be every 200 millisec...
Hello,
I try to use those functions for printing log massages on the Segger RTT terminal, but I have many problems with that.
1. How can I use this function without printing...
Hi everyone,
I am using nRF52832 kit (PC10040), eclipse and softdevice S132 V5.0.0 for developing a BLE service. I follow the service tutorial and I refer to the code from...
i want to connect raspberry pi 2 with nordic thingy 52 via ble.....while issuing connect command after gatttool -I -b Mac addr it is throwing some connection refused error...
i want to know about how nrf51822 module's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
