I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
To check, in sdk 15.0, there are no pca10040e (s112) examples of ble_app_buttonless_dfu & secure_bootloader because examples were not yet ready for sdk 15.0 release, or something...
Hello,
I'm currently using the nRF52832 chips with SDK11.0.0 and s132. I'm currently trying to modify the TX power level for advertisement. I'm seeing many ways that I could...
HI, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v2.0.0) and some other sensors which drivers written by using nRF5_SDK_15.0.0 . Can you help to understand how to do...
Is it possible to program the nRF52840 dongle using the nRF52840-DK using SWD?
I tried, but it failed. From the nRF52840 schematic, it looks the chip is running at 1.8V...
Hi,
Win10 can run a subsystem, which is Ubuntu for me, in the powershell environmental.
But I can not connect the pca10040 debugger. it show error when I try to erase...
I am trying to build a run time test routine that will return the ppm offset between the 32khz and the 16mhz clocks.
Can i use PPI to hook 10 clocks 32khz ticks to capture...
Hi,
MY pca10056 dev board is no longer getting detected. i have gone through this post
here is what i have checked ,
Does the device show up in Device Manager?
No...
Hello!
I use I2S on nrf52832 custom board with ICS-43432 microphone. I try to modify example project.
1. When I2S data_handler function take place, I see a new data (p_data_received...
Nordic team，
mesh sdk： nrf5_SDK_for_Mesh_v1.0.1_src
example: light switch
The client repeatedly configures the server multiple times. After a few configurations, there...
Hello All,
I need some urgent need regarding battery voltage
I am using 8 ADC Channel (ADC0 - ADC7) for different different purpose.( NRF_SAADC_INPUT_AIN0 to NRF_SAADC_INPUT_AIN7...
Hello,
I would like to ask how to use the exemple 'ble_app_blinky' (a device central and a device peripheral) to realize a function like this:
I press a button in one...
I use usbd_ble_uart_pca10056_s140 demo add HID but when bonding fatal error.
this is my code /cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-ef9d92a7ed0649dab15d867bf140c962...
hi, I am doing a project where I have to connect multiple ble peripherals(with different ble services on the different device) with my ble central device and I have to add...
Hi.
I am experimenting with using a nRF52832 to communicate with a nRF24L01+. It is almost working, the nRF52 is sending a packed to the nRF24 ok, and the NRF_ESB_EVENT_TX_SUCCESS...
Hi,
I'am actually trying to develop a BLE based remote, with NRF52832, S132.
This remote must be configured by a smartphone (the remote act as peripheral) and be able...
