Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello....
Is there a way to configure the SPI peripheral(s) to run at a custom bit rate (frequency)?... For example: Run SPI at 3.4MHz.. or any other custom frequency that...
Hello all,
Do you advise to have 2 SPI interfaces - one for the sensors we're using (accelero/ gyro) and another one for the SD card? if so, when adding an SD card to our...
Hi team,
i am having a custom board i want to program soft device and application using external j link. i came across nordic website in this page http://infocenter.nordicsemi...
Hello All,
I am a beginner to NFC OOB, so can you suggest me some good learning materials regarding NFC OOB pairing as I wish to do so between my mobile phone and the...
Good Morning Team,
Hope your day is going well!
Could you please provide the IPC 1752 document and RoHS CoC (2015/863/EU) directive document for below part since it is...
hi hi ;
i'm trying to control gpio pin 20 with my smart phone and with event at gpio pin 5 (when the state of the pin 5 changes the gpio pin 20 toggeles ) but my problem...
Hi, can someone explain in simple terms how it works?
I don't really have a clear concept of what a replay attack is, but I suppose it has something to do with recording...
Hi,
I am facing the same issue for all of the node.js examples.
It says: Connected! Error: command disallowed (oxc)
Also is says: Service uuid XXXXXXX not found!
...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
On nrf52832 and nRF5 Mesh1.0.0
When running idle state(not RX/TX), current comsumption is over 400uA.
And every 100ms, CPU is wake up.(small working.)
What happen...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
Hello. I've got issue with TWI and power down mode. I modificated "ble_app_bps" example, prepared own service and characteristic and I added BME280 sensor. And almost everything...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
