Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello, Thank you for helping me to interface the PCF85176 (40 x 4 universal LCD driver for low multiplex rates) with Nordic nRF52 development kit board. I need to write the...
i have a few question, i bought this " www.skylabmodule.com/.../".
if the device has a sample code loaded?
where are the example codes for the device?
i want connect...
Hi everyone,
I recently acquired a nRF52832 Breakout Board from Sparkfun. I have been using it for a few weeks now and everything was fine. I was programming it using the...
I use DFU function to update APP. and when i execute the flash write operatin in APP,then afer the dfu operation,bootloader can not jump to the APP. it keeps in bootloadr...
I am using nrf52832, SDK14 and sd 132.5.0. I want to disable SAADC after measuring battery level then enable again when I want to measure it again like in this post . When...
Hi, I want to know how to properly indicate for the function
spi_send_recv(...)
that I'm sending or receiving data on SPI.
On other platforms with library function...
I'm using the SPI driver and experiencing a hang in the SPI driver because the SPI interrupt is not raised. The reason is in this code from the driver:
p_cb->bytes_transferred...
Hi,
my device does some UART communication. Because temperature drift of HFINT is to large, the external HFXO has to be used. To make things worse, this is a low power...
hello,
I modified the beacon example that allows me to modify major and minor value from mobile app,
but when i restart the nrf52840 dev board, the modified values are reset...
Hi,
I need to get at least 3 sensors data (Accelerometer and Gyro) simultaneously and I am thinking to use the Nordic Thingy:52 for that. Our application sends these information...
Hello Nordic Devzone,
I have problems with twi/i2c init code on a Micro:bit, nrf51822.
The accelerometer is a Freescale MMA8652FC.
I use Segger Embedded Studio for ARM...
Hi there,
We started to notice that we have been getting random disconnects with the reason BLE_HCI_CONNECTION_TIMEOUT. After profiling our device, it was found on one...
Hello everybody,
I try to use fstorage in SDK 14.2.0 S132 with Segger Embedded Studio IDE.
I write this;
static ret_code_t fds_init (void)
{
ret_code_t ret = fds_register...
I have been using the RF Digital Simblee chip ( also with the NRF51822) with my Android app and Java code to communicate with the Simblee chip as a peripheral.
I have been...
hi nordic;
i need your help, i'm trying to code a control of gpio over the BLE i have an app on android with it i can establish connection and see the service and charactrestic...
