At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I try to run UART/Serial Port Emulation over BLE on SDK v14.2.0 with nRF52 DK and nRF Connect on Android phone following link " http://infocenter.nordicsemi.com/index.jsp...
I am trying to run the coap ipv6 based example code provided in nRF51 IOT SDK. I am using my Linux PC along with a BLE adapter as a BLE enabled router. I can successfully...
I came across this a while ago, however it gives no indication as what releases, of Segger J-Link suite, each nordic J-Link OB download has been tested with.
Is there page...
Hello, I am looking for documentation on the Mesh DFU Protocol. It looks like it is the same DFU that the mesh branch of the nrfutil python app is using. I would like to do...
Hi,
I tried to use fs_erase and fs_store functions but they both return the value FS_ERR_INVALID_CFG which means "Invalid fstorage configuration". I'm working on nrf51822...
Hi,
I'm using SDK 14. I started from ble_uart application, and to use ADC as well I ported ble_app_uart__saadc_timer_driven__scan_mode (SDK 13) to SDK 14 (made changes in...
Hi,
I am implementing the whitelisting feature so that the NRF52 only pairs with one phone at a time. We require the NRF52 to advertise for 10 mins but I could only set...
IN looking at CONN_SUP_TIMEOUT below:
It says the units are 10 ms. if you take 4000 * 10 ms, you end up with 40000 ms which = 40 seconds - not 4 seconds.
Also for...
Hi,
As title, I'm the new for this.
I have one 52840 board and several 52832 boards, and one of them(sink) collect some data from other boards by using proprietary radio...
Hello,
We use nRF52832 with SDK-11 as peripheral in our project. We want to utilize white-list feature to limit the connection establishment. I have studied H ID Mouse example...
Hello, I'm trying to view the STATUS register of the timer (1 for example) but it is not display on the segger registers view ... Is it a well known problem ? Cheers, Sylvain...
I am developing application on nRF52832 with SDK14. I came across mem_section_dummy_rom and mem_section_dummy_ram sections in the linker script in the example codes. I couldn...
Hi
I have been using nRF52 in my project. I am not using provided uart drivers for one uart -> UARTE1. I am using DMA access and I have no problem to send and record messages...
