When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I use same SDK to program the 1.nRF52_DK borad (on broad chip 52832) ,and 2.external program borad chip 52832.
Have a issue, 1.nRF52_DK borad is success to advertisement...
Hey!
Using osx, SES 3.30, importing experimental_ble_app_blinky example from nRF5_SDK_11.0.0_89a8197 to be used with NRF51822 chip. When importing I chose pca10028/s130/iar...
Hello
I am testing with the lis2dh12 sensor and our custom board. I made the LCD test successfully. So I tested the lis2dh12 sensor based on the LCD code, but it failed....
Is there a comprehensive explanation of the usage of uuids_complete, uuids_more_available & uuids_solicited when to use them and how the stack behaves/uses them. I getting...
Hello
First of all, I would like to apologize if a similar question was already asked but all this BLE matter is so broad that it defeats me.
I am planning to put two...
I try to use Eclipse for my nrf project. Previously I used Keil but now, I should to use Eclipse. Anyway, I can build nordic sdk example project but when I work with main...
Hi,
I have posted the same question in the following URL.
devzone.nordicsemi.com/.../
It will be very helpful if you tell me how to get a correct MIC result by AES...
Hello,
I've got some trouble using Nordic Uart Services,
I correctly add the library to my project.
I can receive data from different devices. But when I want to...
Hi, everyone,
I develop the project on N52832 chip when the chip "plays" central and peripheral roles together.
During the running the program I need to check the advertising...
Hello. Everyone.
I'm Aaron and beginner in nRF52832.
I have some serious problems with using the nRF52832.
I'm trying "ble_peripheral\experimental_ble_app_blinky" in Keil...
Hello,
I am using 14.1.0 SDK, I implemented the custom service and characteristic,
but if adding CCCD(Client Characteristic Configuration Descriptor) with the custom value...
Hello,
I am using nrf52 and sdk12.2.2. Can I program this with bootloader and application image at once using nrf go studio?
At present I am first uploading bootloader image...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
We are trying to connect RF51822 with RaspberryPi over Bluetooth. Our aim is to get Light sensor values(lux).
Please advise how to get started with RF1822 Sensor.
*) How...
