Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
2.4g ble work in 2 mode(not same time) when reset.
when I init 2.4g clock
void esb_clocks_start( void )
{
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
NRF_CLOCK->TASKS_HFCLKSTART...
Hello everyone!
I have peripheral device with notify characteristic with 20 bytes length of value and connection time interval - 7.5 ms. So, I want to increase throughput...
Hi,
from the nRF52840's datasheet: Up to 4x SPI masters/3x SPI slaves with EasyDMA .
Is it possible to connect the nRF52840 as a slave with another microcontroller and simultaneously...
Hello,
do I need to do anything to accept new Connection Parameters as a Peripheral when the Central updates them?
I am seeing 'BLE_GAP_EVT_CONN_PARAM_UPDATE' events,...
Hi, guys.
I am meeting a terrible problem when using the SDK14.2 -> BLE\nRF5_SDK_14.2.0_17b948a1\examples\ble_central_and_peripheral
experimental\ble_app_hrs_rscs_relay...
HI,
I am using nrf52 with other mcu and sending scanned beacon to that mcu.
I have set baud rate to 921600 and transmitting data when mcu request.
when mcu request...
Hi,
We am using sdk 12.2.2 and nrf52. We are observing some strange behavior of chip. We have our own customized board.
The issue is mac address shown is different in...
Hi there,
I'm using a PCA10040 board, and the app that I am working on was originally built in SDK 11.0. I'm trying to send a stream of arbitrary bytes over USB using the...
Hello.
I am trying to download a program, but I get this error.
Beacon does not work when downloading in order of Application -> SoftDevice as indicated by the error...
Hello,
In the blinky project, I have added the following peripherals to build up an application
Timer
UART
SAADC
PPI
I have followed the saadc peripheral...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
i have two tablets and one peripheral.Now with the code i have i connect to only one device .if i want to connect to same peripheral with another tablet i have to remove the...
