Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I am using nrf51822 pca10004 with SDK110 v8 , I got a problem that the code hangs in sd_softdevice_enable and stuck in SVC_Handler.
Thanks,
Nagaraj
Sorry for being funny English because I am using translation software.
Hello, I am using PCA 10040.Version is V1.1.0.
I am in trouble because it is recognized as "Bossa...
When I use sdk14.2.0 nus service communication for some time, the connection suddenly disconnected, disconnect reason error code 0x28 ,I do not know what it means, I do not...
Hello,
I am currently using SEGGER studio with SDK11 and the MPU9255 repository from github.com/.../nrf5-mpu-examples . I followed the installation instructions in the...
Hi all,
I have a question that whether it can be set to an equal value with CONN_MNGR_SCAN_INTERVAL and CONN_MNGR_SCAN_WINDOW or not in a S120 application. If I do this,...
I am using the RTC to generate a square wave signal.
I have two issues. One is that nothing I do on the prescaler or the Count Compare is having an influence on the frequency...
When we develop Bluetooth products, we find that in Android 6 APP, Bluetooth devices can connect normally, but at Android 7 or above, sometimes it doesn't connect to Bluetooth...
Just had a contractor update our project (simple device is peripheral and server for some GATT data) from SDK v12.x with S132 4.0.5 to v14.2 with S132 5.1.0.
All works...
nRF52, SDK12.1, Eclipse, gcc 5.4.1, FreeRTOS, no soft-device.
I am having a problem with GPIOTE. I have six interrupts programmed on six different pins. As long as the...
hi everybody
SDK:14.2
Chip:52832AA
NRF GOSTUDIO:12.2.10
JLINK:V9.4
I use NRF GOSTUDIO to write sofedevice or app,it note:
unable to find or open the...
Hi,
I am a beginner with NRF chips, just wanted to know that Can I use different package size for Capacitors/Inductors like 603 instead of 402?
Thanks.
Hello,
Our production systems run on Raspberry Pi, which is running on ARM. Currently the nRF5x command line tools are only available on x86, which means that we need to...
After working with NRF51822, I decided to go for NRF52832, and I bought some modules that have NRF52. I am using GCC and SDK13. I installed the S132 soft device which is in...
Hi - I am using NUS (Nordic UART Service) to send raw sensors data over BLE to my PC for later processing. However, I found that I can not get a more-than-20-packets-per-second...
