Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello,
i am evaluating the nRF52840 on the nRF52840-Preview-DK. I have connected an ADC to the devkit via SPI and my code reads data from the ADC via GPIOTE, PPI and SPIM...
We've got two SPI slaves that we need to talk to with the 52840 (PCA10056 dev kit for now) using SPI Manager. In the initialization of these devices, I'd like to use nrf_spi_mngr_perform...
when I use flash to storage my data,I call the fds_record_write(&record_desc, &record) ,and it return success,but my machine run err, my ble broadcast is missed.I used the...
I'm trying to understand what is meant in section 5 of the BLE on Android primer: "The peripheral device should disconnect itself when it gets disconnected by the client....
Hellou, I am developing application which need data array store to flash manager. I used for some function for storing data (nrf_fstorage_init(), nrf_fstorage_erase(), nrf_fstorage_write...
Hi!
I'm trying to merge the flash_fds example with the ble_app_uart, and the twi example. My intention is to read a value from TWI, store it in flash and then send the...
Hello,
I would like to know how can I configure the parameter NRF_SDH_BLE_GAP_EVENT_LENGTH for a determined NRF_SDH_BLE_GATT_MAX_MTU_SIZE when enabling data extension. ...
hi team,
i was using nrf52840 with sd 5.0 and developed a custom application using ble_app_proximity in 14.1. my use case is my device should hand shake only with my mobile...
In the NRF_SDK_15, only 3 drivers (clock, power, rng) use the return value NRFX_ERROR_ALREADY_INITIALIZED. Why are the others drivers initialization return NRFX_ERROR_INVALID_STATE...
Hello all,
Weve figured out our hardware issues (pin arraignment) and are successfully programming via JLink.
Our goal is to replicate the bootloader/softdevice/firmware...
Hello everyone, I've been trying to get scan_response data from a specific advertiser. Advertiser being nrf52810 running the s112 SoftDevices and Scanner being nrf52832 running...
The S112 soft device and the nRF52810 datasheet both advertise support for BLE LESC, so I think it's reasonable to assume that it should work. However, none of the example...
Hi,
I have code for NRF51822 which used TWI form sdk 8.
Now I want to port it into NRF52840, but I have issues with using old TWI api.
They are located at path .....
Hello,
Is it possible to program nRF51822 with nRF52DK (PCA10056) ?
Currently I am trying to program my custom beacon (nRF51822) connected via SWD P20 header. I am using...
