I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I am using:
NCS 3.0.1 nRF52840DK
My project is based on the coap_client sample, currently running on a nRF52840DK. I have modified it to add the 'observe' option in the...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
I'm planning to build a project using the Nordic Thingy:91X. My goal is to collect sensor data (e.g., environmental or motion sensors) from the device and transmit it over...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
Hi, Is there any resource or sample project to print the thingy:91x onboard sensor values to the serial using the printk? I tried myself with
#define BME680_NODE DT_NODELABEL...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
I am working on stm32 f7 using nrf7002 . My requirement is to work my code on zephyr IDE as same as wifi shell. but for these when I going to add configuration for nrf and...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
