Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
Hi Nordic Community and Developers,
I'm designing a small Bluetooth module using nRF51822 to use it in my next projects and I need to use thinner substrate material (~0...
I have an application that we have ported to the nRF52 that used an EEPROM to manage configuration values. This application doesn't update these values often but when they...
Hi All, we have used Arduino modules based at 24L01+ in our application, now we are getting to apoint where we need to find one of theese or another one and do a redesign...
Hi, I'm searching platform for my project.
I will need to send packets from big quantity of transmitters (nRF24LE1) to one reciever (nRF24L01), it will something like voting...
Hi i am interfacing mma842with nrf51822. but i am not getting data. i have uploaded code. can you tell me what is problem. i don't know i am not getting who am i id try.r...
I've noticed that our custom board sometimes does not work (e.g. execute the code) when the VCC drops to about 0.3V- 0.5V and comes back on again to 3.3V.
For testing I...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
In SDK_v11.0.0-2.alpha, there is a project: examples\ble_peripheral\ble_app_hrs_freertos\pca10028\ble_app_hrs_freertos\s130_with_dfu_pca10028.
But I can't find DFU service...
to # einar thorsrud
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive...
Hi
I am writing an app to utilise the new LESC feature using Diffie Hellman related pairing. I am testing the app against the Nordic provided ble_app_multirole_lesc. I...
with SDK 10 I found 2 SPI libraries, spi_w5_master and nrf_driv_spi . I hesitate between them.
what' the difference between them? and what should I use when I'm using app_timer...
I saw this tutorial:
nRF51 current consumption guide
It's specifically directed to the nRF51, but I guess the principles of Tuning Advertising parameters must be general...
i'm looking to use only one timer for two independent activities:
battery service (as in Nordic examples) and
a routine to detect a certain button press pattern ...
