Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
So I'm currently trying my hand at some very simple things that one can do with the NRF51-DK.
One of those things involves sending notifications to a client on certain...
Hello,
I'm testing n51822 with low voltage mode, and want to check the BOR condition.
Is there any threshold for brown-out reset, or voltage tolerance? e.g. 1.68V...
Hi.
I have received down the source of the example of experimental_ble_app_uart in my keil.
I use register.(NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;)
but, Hardfault occurs...
Hi there,
I am currently using the nRF51 DK trying to teach myself how to create a working ble application. I am currently going through the application note nAN-36_v1...
Hello!
We are using an BLE NRF51822 chip as a GATT-Server, unfortunately without any possibility to modify its software at the moment. The BLE-setup should be very similar...
I want to run the Direct Test Mode for nRF51422 on my board, I'm trying to use the nRFgo Studio.
When I'm trying to connect to the specific COM port, I get the following...
Custom Board which has NordicSemi nRF51822-QFAA MCU,
a temperature sensor (Si7020-A10), and a white LED. The circuit follows the internal LDO setup.
(Ref. nRF51822_PS...
Hello,
i use Bootloader from SDK 7.2.0. I have some questions about init packet handling:
The bootloader compare the device type, device revision and softdevices...
During ble ADV，my device will consume 60uA，when ADV stoped it will drop to 13uA. But when I get ble connected current will up to 130uA.
I test nrf51_sdk_v6_1_0_b2ec2e6...
Hi,
in the new version of S110 (8.0.0) I can see the implementation of scan services:
SD_BLE_GAP_SCAN_STOP, /**< Stop Scanning. */
SD_BLE_GAP_CONNECT, /**< Connect....
Hi,
like many others, I'm confused with Peripheral Passkey Connection.
I'm playing with the ble_app_hrs, in order to be able to setup a Connection Passkey (for the moment...
Just got the S110 SD spec, version 2.0. Very interesting.But I've recently switched from projects on the Keil MDK IDE to the mbed environment (using the nRF5-DK as test platform...
