Hi Nordic Team,
am I currently evaluating the nrf5340 development kit for our new product revision and fail to get a power efficient shell besides rtt logigng.
Concrete...
Hello, guys, I am working on distance measurement project using two nRF5340DK (nrf_dm sample application). I found duration for which the distance measurement between two...
For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Hi all,
I have one question about the deep sleep wakeup process in NRF24LE1. I want to realize the function that "when I press the button, it will cause rise edge on the...
Hi,
I'm testing doing a soft device update (v7.0 to v7.1) over DFU, but I consistently get OP_CODE_SYS_RESET sent to my device after 4 packets(80 bytes), at which point the...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
I'm currently designing a system that requires Nonvolatile memory. Whilst I can accept the 43uS delay to write a word to flash memory. My concern is that it is entirely possible...
Hello,
i plan implementing an block storage for nRF51. I want to integrate an checksum or error correction mechanism.
I have understood i can write an bit 20000 times...
i meet very strange problem! i using nRF51822 QFAC. it has 32K RAM. but when we using 32K RAM Linkscript file. the firmware did not run up. it seem dead in sd_ble_enable(...
Greetings,
S110 with SDK6.0 I try to build the executable for Nordic GitHub project Timeslot Oberver example. I get an error that the handler SD_EVT_IRQHandler is multiple...
