Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi All,
I am novice in this nordic nrf 51822 programming. I wanted to know the best way to do the
following.
I have two different functionalities to be run on eval...
Hi All,
In ble_app_hrs example two function is defined for gpiote_init()
1)
static void gpiote_init(void)
{
APP_GPIOTE_INIT(APP_GPIOTE_MAX_USERS);
}
2)
static void...
Hi
I found there is bonding managing routine in SDK HRM and Proximity examples.
bond_manager_init();
It means in these two case, after pairing with BTLE host, the...
My question is regarding the PPI channel groups. The documentation is extremely limited and leaves many questions.
My goal is to generate 3 PWM signals from a timer with...
If i understand tasks are for outputs and events are for inputs.
Wanted to know relationship between channel and the pin numbers. do they hold the relationship like...
Hello,
I am really confused on how to get a custom BLE service up and running. I have read through nAN-36, and compared the suggestions in that document to the HRS example...
In nRF51 reference manual v2.1 section 18.1.1, it mentioned that the RTC must be able to
run while the 16 MHz system clock (SysClk) source is OFF. 2 questions :
Q1: Since...
Hello,
I'm trying to get the SDK examples working in Eclipse. I have followed all steps(except debugging part) in the nan-29, but i can only import the s110/ble_hrs example...
I am looking for the spacing in mils or mm between the two samtec connectors on the nrfGO board. I am making my board to interface with the PCA10005/PCA10004 and I would like...
Hi,
I'm new to nRF8001 SDK and Bluetooth and I hope my questions are not too stupid lol. So here it goes:
I'm using the Nordic nRF8001 SDK to implement a self-defined...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...