We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I just starting out trying to get an Eclipse dev environment up and running. I've tried following nAN-29 but it seems out of date. The issues I run into are:
CDT...
Hi,
First I want to thank all nordic staff for their great work on sdk & this incredible tiny chip that do a lot :-). I play a little with the devkit sample and my nrf development...
I've got 3 of the 51822 kits: smart beacon, m-kit, and eval-kit.
I've successfully installed Keil uVision 5.1 and developed/loaded applications for eval-kit.
I've successfully...
I'm just trying to determine if I get full SDK access with the nRF51822-mKIT; or if that requires nRF51822-EK/DK? The current posts on the boards seem to be conflicting in...
Hi Nordic team,
Will the S310 stack be kept, feature- and revision-wise, in lock-step with the S110 stack?
To illustrate my question, can we expect the v7 S110 updates...
Hi, guys
I'm facing some problem in RF transmitting. While I used 51822 board being the device and compatible to nrf24LU1 as dongle. To analysis the problem, I need information...
Hello,
i am working with the s110 softdevice and built up a bluetooth communication. I wanted to reduce the number of advertising channels and read about the use of the...
Hi,
I need to send some additional information in advertising.
According to Core Specification Supplement v4 A.1.11 it is possible to use also 128-bit UUID in service...
My keyboard can't work some time,then I read back the hex from device. And I find that there are 4 byte be changed.
if I modify the left 4 red bytes to right. Then programm...
In my opinion, S120 can only acts as central role and can not be discovered by bootloading sponsor which is usually a PC program. More development work is needed if bootloader...
I am trying to run the bootloader example that comes with the SDK 5.2.0 using the softdevice S120 on an evaluation kit, but I am getting an error at the pstorage_init() function...
I'm trying to emulate an nRF24L01+ SPI slave interface with an nRF51822. The nRF24L01+ interprets the first byte in the SPI transfer as a "command", and the data that it will...
Hello,
we experience the situation, where we are able to flash a softdevice (s210) once. After the softdevice is flushed, subsequent attempts to flash the softdevice fail...
I was looking at the product brief for the nRF51922 - which states the SoC can handle both BT BLE and ANT concurrently. The product brief states:
Pin-compatible hardware...
