This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have a test set up using the ble_app_hrs example where I increment a dummy uint16_t periodically and then send that value up to the nRF Toolbox iOS app to plot. I want to...
Hi all,
I would like to use the strcmp - string compare function, however don't know how to create a string from character array. Standard way would be something like this...
I can transmit data from my device (the server/peripheral) with the ble_app_hrs , but want to modify the peripheral behavior with some basic commands sent from the mobile...
I'm migrating from S310 v1.0 + SDK 5.2.0 to the latest S310 v2.0 + SDK 7.1.0 (to be able to update also BL and SD).
I have used OTA DFU based on example included in SDK...
Does the sdk7.1 + softdevice support flash_page_erase function?
Also, for the spi_master api, is the spi_master_event_handler required or optional?
currently, the...
Hi,
How to separate flash memory area that will not be overwritten when you upload new application code (e.g. a few bytes of static data). I'm using Keil.
Hi, I just flashed the BLE_proximity example in the ...\nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310\s110\ble_app_proximity in the nRF51822 Development Kit, and the nFR...
I am working on a custom BLE service on the PCA10001. I can successfully detect and communicate with the PCA10001 using windows x64 MCP. I can also detect and communicate...
Dear Sirs
I am new with Nordic BLE Modules.
After successuful pairing with Windows 8.1 in a Tablet I need to get an active Service. For example I would like to obtain Battery...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
