Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I want to send a one byte payload from the nrf24l01+ (Sparkfun dev board), to nrf52840 DK using the example esb_prx. How should I configure the nrf24 registers to make this...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
Dear all,
I want to implement multiple functions with only one power button, including: 1. Power on/off, Long press to turn on, long press to turn off; 2. Functional response...
I am trying to connect nrf52840 dongle to multiple peripherals(nrf51822) ,so far i combined multilink_c example with uart_c and i can connect and read rssi value of only 1...
Sorry, my English is very bad.
I think I can only express my problem in Chinese.
在使用异步串口时，使用uart_rx_enable()设置的超时时间和真实发生UART_RX_RDY事件的时间相差巨大
using async serial port...
Hi,
We need to interface camera (0.3nrf52840MP to 2MP) with nrf52840 for a new product development. For evaluation purpose, is there any off the shelf camera module which...
I'm trying to add a timer to the usb_cdc_acm example to send a periodic text messages with the timer. I'm building on an Adafruit nRF52840 Feather Express board using Segger...
Hi ,
I am trying to parse the manufacturer specific data that a beacon is advertising.
I can read successfully the company_id but unable to read the "specific data " ...
Hello again Nordic Pro's,
As you probably all know by now, our product app is based on the subject example code, SDK and device. We need to programmatically disconnect from...
I have been trying ti debug with SES and re-installed everything trying to get it to work, for a while it did, but then it began showing this message:
also, it asks me...
