I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Is the data stored in internal flash for mesh encrypted?
Or is any of it encrypted?
I'm talking about the data explained in this link:
https://raw.githubusercontent...
Hi,
I have test setup consisting of 2 boards, one that sends a packet every 2 seconds with CTE, and another with a 2-antenna array that generates MagPhase samples and sends...
Hi,
I am using "http_upgrade_ota" project.
I have added UARTE2 , SPIM3 and WDT peripherals in the application.
To use this peripherals i had to make change in "spm...
Hello, I have developed an application that advertises, connects, pairs/bonds using SEC_JUST_WORKS configuration, and then transmits data at ~2 second intervals to a smartphone...
I would like to use NRF Desktop Connect to connect to, and potentially firmware update an nrf52832 via the onboard bluetooth, but the NRF Desktop connect is only available...
Goodmorning,
I developing an application on nrf52840 board with SDK15.2.0 that communicates via BLE with from the APP nordic. I am started from the example project ble_app_cscs...
So I'm trying to implement Mesh OnOff server with BLE DFU supports. My implementation is as follows:
These are my app_config.h and nrf_mesh_config_app.h
I face...
Hello,
I am trying to use several Thingy 52 as peripheral devices, (sensors) connected to a central (Gateway) particle Argon running ( nRF52840). The idea is to connect...
Hi, I have 2 questions regarding multiple controllers using nRF Mesh.
1. I used the import/export option to transfer the network details from Phone 1 to Phone 2. After import...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
