Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
I am using the RBC mesh in a networking product using the nRF51422. We would like to turn the mesh on and off at selected times, say once per hour for a minute or two. I know...
Hey,
I have been trying to set up wdt for my application which services some interrupts once in a while and advertises continuously. I put the nrf to sleep using sd_app_evt_wait...
Hello,
I'm trying to read voltage signals from a sensor using internal ADC and send them OTA. For now, my codes seems to work, but the only problem with my codes is it...
I'm connecting my nrf51 with my phone and when I move far from the microcontroller (long distance) the connection is lost
what's the function witch rise this error and what...
the code of 51822 PAN 73# must be added in SDK 6.0?
/* Add workaround when starting timer2 */
*(uint32_t )0x4000AC0C = 1; //for Timer 2
NRF_TIMER2->TASKS_START = 1;
/...
hello there i want to interface nrf51 dk with ds3234 using spi. i see spi master example. how to assign SPI I/O pins. can you tell me how to do it?? i find SPIMO_SCK_PIN....
Hello,
I am trying to work with the nrf51sdkv10 and trying to install arm-gnu-gcc toolchain on my MAC-OSx (El-Capitan). I downloaded the 4.9.3 version and installed in the...
