Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
I'm using a nRF52840 configured as Central and Peripheral, with nRF5_SDK 17.1.0 (I'm Not using Zephyr) for reading the Device Name from the Generic Service of a beacon. I...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi all:
I modified DFU-BLE to make it suitable for S130 on nRF51822. I made the following modifications:
On "dfu-ctr1_pt_add"
ble_gatts_attr_md_t cccd_md;
memset...
Hello!
Until now I am using a nRF24L01 with johanson balun (2450BM14A0002) and MIFA.
I want to add a power amplifier to my nRF24L01 project. Can anyone give me advice which...
Hi
I have a programming issue with nRF51822. I am using the nrfjprog.dll to program this microcontroller in my test equipment via J-link Plus. When I have programmed a...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
Is the advertising interval between two packets P1 and P2 defined as:
Interval = P2_start - P1_stop (time between packets)
or
Interval = P2_start - P1_start (time...
In a project I worked on using softdevice s110 v. 7.1.0, if the receiver hadn't enabled notifications, sd_ble_gatts_hvx would return an error, so I used the following construct...
Hi,
I want to advertise multiple UUIDs, one after another
Do I have to stop advertising, or is there a way, that I can update the struct in the background?
Currently...
I have two UART devices on a custom board with an nRF51822. I've just upgraded the SDK I use from 8.1.0 to 10.0.0 and one of the UART connections has stopped working, but...
Totally get the limitation of 3 PWM channels.
Wondering if I can dynamically re-assign which 3 pins are tied to the PWM outputs.
At boot time, I call this function:...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I have got reliable writes working on nordic side (nrf51822 eval board).
Tested them with master emulator dongle by using write long button on MCP on PC.
I...
