Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I connected to nRF51422 and nRF52823 by mesh SDK.
now I want to connect with nRF51822.
is there mesh SDK for nRF51822?
if not, which code in nRF51422 should...
Hello everyone~
I need to use 2 UARTs to connect to different chips. If I use nRF82832, can I use 2 GPIO pins to simulate another UART? I just use it for one byte or two...
Does the nRF52810 have a wake on low power comparator from OFF mode?
This is a feature that exists on nRF51822, but I cannot seem to see it in the nRF52810 as a feature...
Often, I create and download Macros and the 'play' icon is in the lead-line of the macro but after import to nRF Connect, the macro cannot be played and is NOT blue but rather...
Hello,
I am using sdk12.2 and nrf52. I want to send more than 8 packets of data to nrf app. How can I do that?
My code snippet is as follows:
enter code here
void...
Log-2018-01-12-11-49.txt When I use the nrf connect app to connect my device, it often does not connect to my device.And i see the error on the log is： ERROR 22 GATT_CONN_TERMINATE_LOCAL_HOST...
I have learned that the "sd_power_dcdc_mode_set ()" function does the appropriate mode switch.(LDO and DCDC)
I learned from the following URL.
devzone.nordicsemi.com...
Hi to everyone!
It's the first time I use and program clocks in a device. I'm very lost with crystals, power management and this stuff.
I have a custom board with two...
I am trying to flash custom firmware to Thingy using nrf52dk and nrfgostudio.
I have attached a cable from the debug out port on the DK to Thingy, and followed the steps...
Hello,
I'm using the nRF51822 QFAA and I just came out to this problem:
Is this still unsolved? I always end up in the same forum threads and making 0 progress on how...
About the PCB antenna layout of nRF52810, can i directly copy the reference layout provided by Nordic and paste it on my PCB?
Below PCB layout photo, is i directly copied...
I am about to start using the nRF52 for several projects and would like to know which version of Eclipse is recommended? Since Eclipse can be customized in many ways I'm looking...
i took the original sdk 14.2.0 s132-5.0 ble-uart nus-service example for reference measurements to send data from a 52832 to an android device running nrf uart v2.0
to...
I need to add two more led pins - #10 and #30 - to that board, but I don't know what to do with LED_START and LED_STOP lines, and so far, it is difficult for me to trace any...
