I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
My first objectif is that the Micro:Bit consumes less than 2ÎĽA without the BLE. I read that the Micro:Bit program was not powered if the Micro:Bit is powered by the...
Hi everyone,
I am writing a program in Keil whereby I have to send a large amount of data through BLE notification in real time. The program works by having two timers...
I want nRF52832 to be a central device which will take an input from nRF51822 (peripheral device). Also, Is it possible to make two nRF51822 talk to each other?
Hi,
I having an nrf52832 board and using gnu arm, nrfjprog to program the device. i reading data from two different sensors using spi and TWI in two different codes. now...
Hello all,
I have received "nrf51822 smart beacon kit" connected the battery power and i can detect the device in nrf Beacon app. but the issue is when i select the actions...
I am going to have streaming data come through a characteristic on an S110 device. When the client writes to the characteristic, my peripheral device will read the characteristic...
How do I use Wireshark to see the connection interval negotiated between my nRF51822 peripheral and a central which is a mobile app? Which messages should I be looking for...
Hi all,
I am not very proficient in NORDIC and BLE. I was wondering if you could answer me.
I am developing a module using NRF52. I have a redundant wireless communication...
I am using a PCA10040 with a nRF52832 mounted on it. I am trying to match the IC revision with the packet variant as explained here .
The problem here is that the chip...
Hi I am new to Nordic development and set up all the tools required for compiling and flashing program to nrf52840 0n ubuntu. I downloaded nrfjprog and jlink segger and put...
Hello,
I'm trying to use a nrf51 dongle (PCA10031) as a BLE sniffer. I'm following the ble-sniffer_win_1.2_User Guide.pdf.
On the required software, i need to install...
Hi,
I try to use the example ble_peripheral -> blr_freertos -> ble_app_hrs_freertos and I add to the thread a fds_register() and fds_init(). Problem: In the call back function...
Hello, I am using the NFR52 DK (s132) in peripheral mode. I have implemented a pairing mode based on a static passkey. However, the available time to enter the key in the...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
