HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using the S120 stack and wish to connect and control as quickly as possible to the peripheral. The central and peripheral devices are both embedded devices and are...
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
I am using blenano with mbed compiler and a 24LC256 eeprom.
the output o screen I get is the no. of total chars, i.e, 65355. below is the code.
#include "mbed.h"
#include...
Hi guys,
I'm on Win7 and I'm writing data from libusb to nrf51 board, my code is
usb_bulk_write(dev_handle, 0x04, data, WRITE_SIZE, 1000);
When the nrf51 receives...
Hello:
I tried to find this in the documentation but could not. Regarding the external trigger to the PPK (TRIG IN pin). Does this require a high-to-low transition, a low...
Do I need a custom 128-bit UUID if I delete one or more Characteristic from an Adopted Service
I do not modify the remaining Characteristics
For instance: Sniffing with...
I'm trying to program Sparkfun nRF52832 board using SWD (via nRF52 DK). I've erased original bootloader/softdevice/app and programmed S132 and my app. The app works, but only...
Hello,
I'm beginner for NRF51822. I have tried ble_app_hids_keyboard example on NRF51822 with s130 softdevice.
It is discoverable in smartphone as Nordic_Keyboard. Smartphone...
We have been using the DFU that came with the sdk 12.1 with a modification (essentially removing the button from the DFU code). We currently send an application command that...
Hardware:
I have an nRF52 device running the S132 running as a Central.
I have 6 iOS/Android devices running as peripherals.
Background:
I am attempting to have my central...
Hello,
is there any good example available, with whom I can simulate, that there are two devices are already connected and the host is scanning for some other devices?...
I am trying to use the function or any function with my BLE UART application. I have a timer that expires to kickoff reading of some sensors and then when I try to read my...
Hi all,
i m connect a sensor with Nrf51822 beacon and get the data.
so i want to transfer those data to Nrf51 dk kit continuously.
where i want to change or put my data...
Hi,
I use nRF51422 in Dual mode(SD310) with SDK10 Version.
The profile is CSCS.
I want to ask
How to just show Speed Sensor or Cadence Sensor.
Here is what I did just...
