Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hello,
I have some questions regarding S110:
Is it possible for the S110 softdevice to scan for broadcasts?
Is it possible to create a connectable broadcast...
Hi all,
I'm trying to implement two hex files into my processor, one application and one bootloader.
In nRFgo Studio I enabled 2048 bytes in the NUPP field to get a protected...
I've been working with writing and erasing flash. And somehow I can't flash softdevice 6.0 into the NRF51822 G0 chip with NRFGO. The error information poped up is "An error...
Hello,
For my application i need one central device collecting data from sensors. For central side i would choose for the nrf51822(s120), simply because it has high priority...
I know it was asked and I was searching but I didn't find a clear answer about that. I know that I can generate any random 128bit UUID for all my user services & characteristics...
Hello,
I am using nRF51422EvKit with Heart Rate Monitor example. Device is detected by PC (Windows 7) but in device manager appear "External Bluetooth device" with marking...
Hi,
We have a custom board with nrf51822 chipset, when i try to flash ble_app_proximity application through keil, it is giving advertisement, but i cannot able to connect...
I have a custom PCB and i have connected the MISO,MOSI,SCK,REQN and RDYN line from the nRF 8001 to Arduino. And uploaded your code of ble_uart_project.ino but nRF 8001 does...
Executing:
nrf_gpio_range_cfg_input(0, 39, NRF_GPIO_PIN_NOPULL);
I believe it will.
I know the range should end at 30 but I hit the wrong key when I coded it. So...
I have a characteristic that is 80bytes long which is sometimes read by the client using long read. I also want to send the complete attribute value when its state changes...
Hi guys,
i tried to find information about the differences in chip revision
nRF51822-QFAA-R7, NRF51822-QFAA-T and nRF51822-QFAA-G0 but i can't find the R7 or T type anywhere...
1.
Are there any other resources than RTC/WDT requiring 32kHz LFCLK, not listed in Table 28 of nRF51422 PS (i.e. Radio)?
2.
ANT stack requires LFCLK +-50ppm, so +-25ppm...
Hello,
I'm getting an exception while starting MasterEmulator Sample Programs. All indicated Dlls were copied along with .exe, windows ver is 7. the same error happens...
Hello all,
I would like to send Acc and gyro data just like health temperature over nRF8001. Which Service can I use? How can I create one?
Thanks for help in advance...
