I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
This may be an obvious question, but I wanted to make sure that my assumptions are correct.
The nRF51822 is able to use an external 32kHz crystal oscillator for its low...
In the 51422 Prod Spec v2.0 it states that “high performance RF capacitors” for the X7R decoupling caps should be used.
Is High performance RF equivalent to a “High...
Hi,
I am trying the Direct Test Mode (DTM) function integrated into the nRFgo application. I am using the nAN-34, Dev Kit User guide, and help (F1) in nRFgo as documents...
I use DK usb dongle to catch data from my ble device , but I can only catch the broadcast data . When the ble device is connected to PC ble dongle , I can't catch data any...
I have Olimex Mod-nRF 8001 Module which i bought it from here . It has break out the RDYN,REQN,MISO,MOSI,SCK and reset pins. My question is can i connect RDYN and REQN lines...
I used the Nexus 5 with android OS 4.4 and try to
use both the "Master control panel" and "Toolbox" Apps to upload firmware.(DFU)
When I use the "Master control panel" App...
We are using an nRF51822 with s110 v5 and an iPhone. When the iPhone connects to the nRF51822, occasionally (perhaps 1/4 of the time) the iPhone fails to complete service...
Having some issues with the examples on the nRF51822 development kit. Hoping someone can help.
Working from nRF51822_Development_Kit_User_Guide_v1.3.pdf.
Motherboard...
Hi all.
I am making a PCB for nRF51822. My PCB need is to talk with iPhone for BLE Proximity application. Also I need to control a LED from iPhone. And I need to get low...
In short: Is it feasible to use RSSI values when tuning the antenna?
I have a custom board with an nRF51422 on which I have designed the RF part to be as much as possibly...
Any suggestions for handling a bricked custom board?
I'm pretty sure I know where the problem is in my code, but now I can't reprogram the board. I did have this happen...
Hi, I'm developing an BLE application using nrf51822.
I have a BLE security issue to discuss.
(Actually I don't have much network security background...)
In our application...
I'm using PCA100001 board with pure-gcc Makefile and s110_nrf51822_5.2.1_softdevice.
And I'm writing simple code customizing s110 samples like below:
static void ble_stack_init...
