void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
After using comand line --rbp, recover fail,the nrfjprog error log as below:
--------------------------------------------------------------------------------
nrfjprog...
Recently I have been learning ble_app_uart routine, here is a question
When receiving the message sent by the client, nus_data_handler this function will be softdevice...
Hello,
I succeeded to port s110 & sdk9 to s140 & sdk14 which was a problem before.
What we need to do now is to compare the performance of BLE devices with s110 & sdk9...
Hi, I am a beginner programmer and I have the next problem.
I am working with nRF52832 SDK 12.2 trying to send AT commands to an ESP8266. I send the AT commands byte by...
Hi all
According to errata 146 of the nRF52832 Rev 1 errata sheet V1.5, the LFRC oscillator has a frequency tolerance of 500ppm instead of 250ppm.
What are the consequences...
I have a bootloader compiled from SDK 14.0, and when I try to upgrade to 14.1, the new linker script (secure_dfu_ble_gcc_nrf52.ld) does not contain the UICR_BOOTLOADER memory...
Hi,
I'm using the nrf51822 and I want to merge Server and Client roles in one Peripheral device. I am already able to send a history of temperature and humidity measurements...
Sometimes when the method RequestData is called after receiving a notify on the characteristic, the Master Emulator seems to hang for a set amount of time before throwing...
Hi guys,
I have troubles with MCP 3.10.0.14 but the device (PCA10031) cannot be detected in my laptop (Win 7 enterprise). I actually checked it on other PCs and everything...
Hi, I have just taken on responsibility for maintaining some firmware written for the nRF24LE1. One file, radio.c, contains the copyright header:
/* Copyright (c) 2008...
Can a proxy node also be a client and server node (a controller node)?
What are the key differences between a server and a client in BLE mesh?
Can a server relay a packet...
Hi,
When I try to download code to my nRF52832 from Keil with the example "BLE ATT_MTU Throughput Example", I get this error: Error: Flash Download failed - "Cortex-M4...
i want make delay funtion by timer?
in the other MCU like PIC, AVR, stm. i find register that hold value counter and i cant set this value
for example:
timer 8 bit will...
Hello
Just to confirm:
is it OK to use 2-layer PCB with nRF52840?
In case a 4-layer is needed, when do you advise the use of a 4-layer pcb?
Basically we...
